X22 Snowboarding founder Joel Powell experienced this very thing when he broke his wrist in two places when he was getting off of the lift while using an ordinary stomp pad that was iced over. The problem with most stomp pads is that they ice over once you have made a couple of runs down the hill, which creates a little icy bump on your board where your foot could slip off. Most of the stomp pads made up until this point have been made out of plastic, rubber, of small metal studs. Us snowboarders are at a disadvantage because we can only have one foot in the binding on the way up, because we need to skate our way around the lift lines. Stomp pads or traction pads have been used since the early days of snowboarding, due to the fact that chairlifts were designed for skiers, not snowboarders. As snowboarding has evolved over the last three decades, snowboarding equipment has dramatically improved, which has helped push the sport and the riders to new heights never achieved before. The strategically placed spike patterns lock into the snowboarders boot and provides stability that no other stomp pads can offer. The X22 spike pad gives the snowboarder an unprecedented level of control and stability. As most snowboarders know, getting off the chairlift can be a challenge, especially when there are other fallen riders in the landing area. They are hand crafted in the USA and built to last. Make sure you press down hard on the stomp pad after you put it on your board to remove any air that might be trapped in there.Upgrade your Stomp Pads to a Spike pad X22 spike pads are made from lightweight aerospace aluminum alloy and silver coated stainless steel spikes. The hairdryer helps make the adhesive extra sticky from the jump. When you figure out where you want to place it, grab a hairdryer and heat up the spot on the board and also heat up the adhesive that’s on the bottom of the pad when you peel of the bottom. The best spot is right in front of the back binding so that the boot can lean on the binding for some extra control. Next, make sure you know where the pad needs to be placed on the board to be effective. It’s not a bad idea to go over the area on the board with a household cleaner just to remove any dust or grime. First off, make sure the board is clean and dry. Mounting a stomp pad is easy and if you take the few extra minutes to do it right then it will never fall off. I’d go with a rubber pad with studs for extra grip and also because you can use it to scrape snow from the bottom of your boot. I don’t know if they got knocked off from use or if they just can’t stick to the board when it gets really cold. One quick note on the metal studs-I’ve learned from experience that most of the stud stomp pads end up falling off. Stomp pads do help your deck from getting all scratched up but you end up with a big piece of rubber or some metal studs covering the design on your board. If you hate getting off the lift and it stresses you out then go for the stomp pad.Īnother popular pro-stomp argument is that the stomp pad will protect your board from getting scratched. You can still get some grip on your board by resting your free boot against the back binding. But what about when I get off the lift, bra? I’m with you on that one-sometimes those ramps at the top of the chair are way too steep and extra icy. You’re either skating over to the lift at the bottom of the hill, you’re getting off the lift, or you’re stuck in a flat spot on some ridiculous green trail at a sick New England ski resort with 1400’ vertical and a snack bar that charges eight bucks for a cup of soup and an extra dollar for oyster crackers and you want to kill yourself because you just paid 80 bucks to go downhill but you’re stuck in a flat spot and you wish you just learned how to skateboard and never spent five hundred bucks on a sick reverse rocker shred sled with a picture of a cow skull and a pirate ship. There are only a few instances when you actually snowboard with one foot. Last time I checked, I observed that most snowboarders, while snowboarding, strapped their feet into those things called bindings. No, dude, you don’t need to mess up your crispy new snowboard with a big piece of studded rubber or metal. Customers in the shop often ask if they need to put a stomp pad on their brand new board.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |